Search results for '%252C4 mm'

This thin plate magnet is perfect for sewing into light fabrics. The 6x6mm surface area gives plenty of holding strength, but the thin profile ensures that the field does not extend too far. This is our smallest plate magnet available. Learn More

Do not under estimate the power of this large cube magnet. With a holding capacity of up to 70 lbs, this magnet is definitely not for the un-initiated. This one creates a very deep magnetic field that is perfect for detecting metal studs in the wall, building particle accelerators, or very large halbach arrays for your maglev train. Magnets this large can be dangerous and should always be handled with thick leather gloves. This magnet is very difficult to control and easy to break. It is not recommended for day to day handling and experimentation. The B2525 can hold up to 70 lbs. Learn More

Tiny cylinder magnet. 1mm diameter and 3mm thick with gold plating in grade N48. Can be custom produced with any plating or material grade. Useful for jewelry, electronics, sensor and craft applications Learn More

This is a very useful style of magnet. The magnet is set inside of a protective steel cup. The assembly has a countersunk center hole that is perfect for mounting with a screw or bolt. The steel cup serves several purposes. Besides protecting the magnet, the cup will also focus the magnetic field to the front of the assembly. Learn More

37mm dia. x 6.5mm inner dia. x 12mm thick Neodymium Ring Magnet - NdFeB N38 - Nickel Plated - Axially Magnetized through 12mm thickness Learn More

This is also the Disk #08 mentioned on the audiworld forums for the detachable license plate kit.
Learn More

A small thin rare earth magnet that works great for paper crafts, modeling, figurines, sensors and jewelry Learn More

9mm dia. Neodymium Sphere Magnet - NdFeB N38 - Nickel Plated - Magnetized through 9mm diameter Learn More

One of our most popular cylinders. This one is easy to handle, great for crafting wood working, plastics, office cubicles, and more. It wont pinch your fingers and it can hold around 2 lbs. Learn More

This small ring magnet is easy to handle and does not pinch fingers. It is shaped like a tube with its poles located on the ends with the holes. Learn More

One of our most popular Sizes. Learn More

An extremely tiny square magnet. Approximately 1/16th of an inch wide by 1/32" thick. The poles are located on the 1.5 x 1.5mm surfaces. Learn More

This medium cube can hold up to 15 lbs. It will take a little effort to separate two of them that are stuck together. Learn More

This magnet is a good size for crafts and woodworking. It is small enough that it wont pinch fingers. Commonly used in magnetic badge holders or lapel pins. Holds up to 7lbs. Learn More

This is a very useful style of magnet. The magnet is set inside of a protective steel cup. The assembly has a countersunk center hole that is perfect for mounting with a screw or bolt. The steel cup serves several purposes. Besides protecting the magnet, the cup will also focus the magnetic field to the front of the assembly. Learn More

25mm dia. x 4mm inner dia. x 5mm thick (with 8mm dia. x 3mm deep countersink) Neodymium Countersunk Ring magnet - NdFeB N38 - Nickel Plated - Axially Magnetized through 5mm thickness Learn More

18mm dia. x 3mm thick Neodymium Disc Magnet - NdFeB N38 - NiCuNi Plated - Axially Magnetized through 3mm thickness Learn More

This is the same size as our D0301 and D0301G disc magnets. Learn More

3mm dia. Neodymium Sphere Magnet - NdFeB N38 - Nickel Plated - Magnetized through 3mm diameter Learn More

This diametrically magnetized magnet was originally designed for the Melexsis MLX90316 Rotary Position Sensor IC. Cylinder magnets are usually magnetized so that the poles are on the ends of the magnet. This piece is setup so that the poles are on the sides of the magnet. This makes the magnets stack up edgewise. The side effect is that this magnet is perfect for magnetic jewelry. See our magnetic bracelet combo pack.

Learn More

32mm Hook Magnet, NdFeB Grade N38, Nickel Plated Learn More

This is a very useful style of magnet. The magnet is set inside of a protective steel cup. The assembly has a countersunk center hole that is perfect for mounting with a screw or bolt. The steel cup serves several purposes. Besides protecting the magnet, the cup will also focus the magnetic field to the front of the assembly. Learn More

This is a thin plate magnet that can be sewn into light fabrics. The large surface area gives plenty of holding strength, but the thin profile ensures that the field does not extend too far. This magnet can hold up to 12 lbs. Learn More

A strong medium sized disc magnet with gold plating and a dimple marking the North pole. Learn More

A good sized cylinder magnet that is a little bit less than 1/2 inch in diameter x 1 inch long. Like all cylinders, this one is best used when you need a deep magnetic field and not merely holding power. Learn More